Product image from the manufacturer or its official distributor, reproduced to identify the model (legal notice).
SPARKX i7
The Creality SPARKX i7 is a FDM 3D printer released in 2026 by Creality, with a build volume of 260×260×255 mm and MSRP of €403. Compatible with CFS (4 slots). Claimed maximum speed: 500 mm/s.
Manufacturer's suggested retail price (MSRP). Not the store price — the actual price may vary.
Our take on the SPARKX i7
The SPARKX i7 is Creality's pitch for beginners who want colour from day one: an open 260 × 260 × 255 mm printer with a 300 °C nozzle, a camera and support for the 4-spool CFS. It weighs just over 9 kg, so it fits on a shelf or an ordinary desk.
It goes head to head with the Bambu Lab A1, which has a very similar volume and approach with the AMS lite. Within Creality, the K2 SE is an even cheaper route to multicolour, with slightly less volume and no camera.
Worth knowing: its claimed acceleration (10,000 mm/s²) is half that of many rivals, so on parts with lots of direction changes don't expect the times of the fastest machines. It's open-frame with a 100 °C bed, so ABS and ASA come with caveats. And remember single-nozzle multicolour always purges filament at each change.
Written from its specs and the sources cited at the end of this page; we haven't tested it in person.
Technical specifications
| Technology | FDM |
|---|---|
| Build volume | 260×260×255 mm |
| Weight | 9.12 kg |
| Max speed | 500 mm/s |
| Max acceleration | 10,000 mm/s² |
| Max nozzle temp | 300 °C |
| Nozzle material | — |
| Drive | direct |
| Flow rate | — |
| Max bed temp | 100 °C |
| Bed material | PEI |
| Auto-leveling | Full-auto leveling |
| Enclosed | No |
| Heated chamber | No |
| AMS compatible | Yes (CFS (4 slots)) |
| WiFi | Yes |
| Camera included | Yes () |
| Official slicer | Creality Print |
| OrcaSlicer support | — |
| Power | 700 W |
| Noise | — |
What materials can the SPARKX i7 print?
This comes from four facts on its spec sheet: the nozzle reaches 300 °C, the bed 100 °C, and the machine is open-frame with a direct-drive extruder. Those four facts decide most of the list: nozzle temperature sets the ceiling on what you can melt, the bed decides whether the first layer sticks, the enclosure keeps large parts from warping, and the extruder type rules flexibles. We don't test the machine — this is guidance derived from verified data, not a guarantee.
In short: it prints PLA, PETG, TPU (flexible) without a fight, and it can reach ABS, ASA, Nylon (PA), Policarbonato (PC) with conditions — the detail for each is below.
| Material | Prints it? | Why |
|---|---|---|
| PLA | Yes | Yes. PLA has no special needs: any FDM printer like the SPARKX i7 prints it out of the box. |
| PETG | Yes | Yes. With a nozzle up to 300 °C and a bed up to 100 °C it comfortably meets PETG's needs. |
| TPU (flexible) | Yes | Yes. It has a direct-drive extruder, ideal for flexibles; prints TPU well (go slow). |
| ABS | With caveats | With caveats. It reaches 300 °C, but it's open-frame: ABS can warp and ventilation is advised. Doable in a draft-free spot or by adding an enclosure. |
| ASA | With caveats | With caveats. It reaches 300 °C, but it's open-frame: ASA can warp and ventilation is advised. Doable in a draft-free spot or by adding an enclosure. |
| Nylon (PA) | With caveats | With caveats. It reaches 300 °C but is open-frame; Nylon warps in drafts and absorbs moisture. Enclosure + drying almost mandatory. For carbon-fibre variants, use a hardened-steel nozzle. |
| Policarbonato (PC) | With caveats | With caveats. It has the temperature (300 °C) but is open-frame; PC warps badly without an enclosure. Only with one added. For carbon-fibre variants, use a hardened-steel nozzle. |
Need the materials it struggles with? These printers handle them
ABS, ASA, Nylon (PA), Policarbonato (PC)
Popular comparisons
Own the SPARKX i7? Write a review
User opinions, moderated before publishing. hotend doesn't verify purchases.
Sources & references
Specs cross-checked against these public sources:
- Creality Official Store - SPARKX i7manufacturer
Specs checked against the sources cited above on 19/06/2026. Confidence in the data: high.