Product image from the manufacturer or its official distributor, reproduced to identify the model (legal notice).
K2 Plus
The Creality K2 Plus is a FDM 3D printer released in 2024 by Creality, with a build volume of 350³ mm and MSRP of €1,499. Compatible with CFS (4 slots). Enclosed chamber. Active heated chamber. Claimed maximum speed: 600 mm/s.
Manufacturer's suggested retail price (MSRP). Not the store price — the actual price may vary.
Our take on the K2 Plus
The K2 Plus is Creality's large enclosed printer for demanding materials: 350 × 350 × 350 mm, an actively heated chamber up to 60 °C, a hardened-steel nozzle up to 350 °C and a 120 °C bed. With the CFS it takes 4-spool multicolour, and its claimed 40 mm³/s flow is among the highest in the catalogue.
Its most direct rival is the Anycubic Kobra S1 Max, with the same volume, a chamber heated up to 65 °C and ACE Pro multicolour. The K2 Plus answers with LiDAR plus strain-sensor levelling, a quick-swap nozzle and wired Ethernet. For people who prefer Prusa's open ecosystem, the CORE One+ is the alternative, with less volume.
The downsides are size and power: it weighs about 27 kg, takes a whole table and its rated power is 1,000 W (if the bill worries you, see how much electricity a 3D printer uses). For PLA and small parts it's far more machine than you need.
Written from its specs and the sources cited at the end of this page; we haven't tested it in person.
Technical specifications
| Technology | FDM |
|---|---|
| Build volume | 350³ mm |
| Weight | 27 kg |
| Max speed | 600 mm/s |
| Max acceleration | 30,000 mm/s² |
| Max nozzle temp | 350 °C |
| Nozzle material | hardened steel |
| Drive | direct |
| Flow rate | 40 mm³/s |
| Max bed temp | 120 °C |
| Bed material | PEI plate |
| Auto-leveling | LIDAR + strain gauge |
| Enclosed | Yes |
| Heated chamber | Yes |
| AMS compatible | Yes (CFS (4 slots)) |
| WiFi | Yes |
| Camera included | Yes (1080p) |
| Official slicer | Creality Print |
| OrcaSlicer support | Yes |
| Power | 1000 W |
| Noise | — |
What materials can the K2 Plus print?
This comes from four facts on its spec sheet: the nozzle reaches 350 °C, the bed 120 °C, and the machine is enclosed with a direct-drive extruder. Those four facts decide most of the list: nozzle temperature sets the ceiling on what you can melt, the bed decides whether the first layer sticks, the enclosure keeps large parts from warping, and the extruder type rules flexibles. We don't test the machine — this is guidance derived from verified data, not a guarantee.
In short: it prints PLA, PETG, TPU (flexible), ABS, ASA, Nylon (PA), Policarbonato (PC) without a fight.
| Material | Prints it? | Why |
|---|---|---|
| PLA | Yes | Yes. PLA has no special needs: any FDM printer like the K2 Plus prints it out of the box. |
| PETG | Yes | Yes. With a nozzle up to 350 °C and a bed up to 120 °C it comfortably meets PETG's needs. |
| TPU (flexible) | Yes | Yes. It has a direct-drive extruder, ideal for flexibles; prints TPU well (go slow). |
| ABS | Yes | Yes. Nozzle up to 350 °C and an enclosure: it contains ABS's warping and fumes. |
| ASA | Yes | Yes. Nozzle up to 350 °C and an enclosure: it contains ASA's warping and fumes. |
| Nylon (PA) | Yes | Yes. It reaches 350 °C and is enclosed: it prints Nylon (dry it well first). For carbon-fibre variants, use a hardened-steel nozzle. |
| Policarbonato (PC) | Yes | Yes. Nozzle up to 350 °C and an enclosure with active heating: suitable for PC. For carbon-fibre variants, use a hardened-steel nozzle. |
Popular comparisons
Own the K2 Plus? Write a review
User opinions, moderated before publishing. hotend doesn't verify purchases.
Sources & references
Specs cross-checked against these public sources:
- Web oficial fabricanteManufacturer page
Specs taken from the sources cited above; we have no recorded date for the last check. Confidence in the data: medium.